The Geekvape Z Tank is a sub-ohm tank that is compatible with a variety of coils. It is a great tank for those who are looking for a flavorful and dense vape. Changing the coil on the Geekvape Z Tank is simple and easy. By following the steps below, you can change the coil in just a few minutes.
First, you will need to remove the mouthpiece from the tank. To do this, simply pull the mouthpiece straight up. Once the mouthpiece is removed, you will see the top cap of the tank. Unscrew the top cap by turning it counterclockwise. Once the top cap is removed, you will see the coil. Grasp the coil and pull it straight out of the tank.
To install a new coil, simply insert the new coil into the tank and push it down until it is seated. Screw the top cap back onto the tank and hand-tighten it. Finally, replace the mouthpiece on the tank. Your Geekvape Z Tank is now ready to use.
Preparing the Geekvape Z Tank
1. **Gather your materials.** You will need the following items to change the coil in your Geekvape Z tank:
- A new Geekvape Z series coil
- A Phillips head screwdriver
- A pair of needle-nose pliers
- A paper towel or tissue
2. **Disassemble the tank.** Start by unscrewing the top cap of the tank. This will reveal the chimney and coil. Grip the chimney firmly and unscrew it from the base of the tank. Be careful not to overtighten or cross-thread the chimney.
3. **Remove the old coil.** Once the chimney is removed, you will see the old coil. Use the needle-nose pliers to grip the coil and pull it straight out of the chimney. Be careful not to damage the O-rings on the coil.
4. **Install the new coil.** Take the new coil and insert it into the chimney. Make sure that the coil is properly aligned and that the O-rings are seated correctly. Use the needle-nose pliers to tighten the coil into place.
5. **Reassemble the tank.** Screw the chimney back onto the base of the tank. Be careful not to overtighten or cross-thread the chimney. Screw the top cap back onto the tank. Your Geekvape Z tank is now ready to use.
Identifying the Z Series Coil
Geekvape Z Series coils are specially designed for the Geekvape Z Tank. They come in a variety of resistances to cater to different vaping preferences and styles. Here’s how you can identify the Z Series coil:
Coil Size and Resistance
The Z Series coils come in various sizes and resistances. The most common ones are:
| Coil size | Resistance |
|---|---|
| 0.2 ohm | 70-80W |
| 0.25 ohm | 45-60W |
| 0.3 ohm | 30-45W |
| 0.4 ohm | 25-35W |
| 0.5 ohm | 20-28W |
| 0.6 ohm | 15-25W |
| 0.8 ohm | 12-18W |
| 1.0 ohm | 10-16W |
| 1.2 ohm | 8-12W |
The resistance of the coil determines the power output and vapor production. Higher resistance coils produce less vapor at lower power, while lower resistance coils produce more vapor at higher power.
Coil Type
Z Series coils are available in different types, including:
– Single-coil: These coils have a single heating element.
– Dual-coil: These coils have two heating elements.
– Mesh-coil: These coils have a mesh structure that provides a larger surface area for vaporization.
– Triple-coil: These coils have three heating elements.
– Quad-coil: These coils have four heating elements.
The type of coil affects the flavor, vapor production, and lifespan of the coil.
Removing the Old Coil
To efficiently replace the coil, you need to first remove the existing one. Here’s a detailed guide to help you do that:
Step 1: Empty the Tank
To start the process, empty any remaining e-liquid from the tank. Remove the top cap and carefully pour out the liquid into a safe container.
Step 2: Unscrew the Base
Once the tank is empty, turn it upside down and unscrew the base. This will detach the base from the rest of the tank.
Step 3: Grip and Pull the Old Coil
Locate the old coil inside the base. It will be connected to the base via two O-rings. Firmly grip the coil’s base (the metal part where the O-rings are located) and pull it straight out of the base. Use a paper towel or cloth to assist with the grip if needed. Be gentle to avoid damaging the coil or O-rings.
Aligning the New Coil
4. **Screw the coil clockwise into the base until it is snug**: Hold the coil upright and align the threads with the corresponding threads on the base. Ensure that the coil is not cross-threaded by carefully aligning it before screwing. Once the coil is properly aligned, begin screwing it into the base by turning it clockwise. Tighten the coil until it is snug, but avoid overtightening as this can damage the threads or the coil.
Additional Tips:
| Tips |
|---|
| Lightly dampen the coil with e-liquid before inserting it into the base to help prime it and prevent dry hits. |
| When aligning the coil, ensure that the airflow holes on the coil are facing the airflow slots on the base for optimal airflow. |
| If the coil is not screwing in smoothly, check for any debris or damage that may be hindering the process. |
| Once the coil is securely tightened, reattach the base to the tank and fill it with e-liquid to prime the new coil before vaping. |
Inserting the Coil
When it’s time to replace the coil in your Geekvape Z Tank, follow these steps to ensure a hassle-free experience:
1. Disassemble the Tank
Start by unscrewing the top cap and removing the mouthpiece. Then, remove the base from the atomizer.
2. Remove the Old Coil
Grip the base of the coil and pull it straight out of the atomizer.
3. Prime the New Coil
Before inserting the new coil, apply a few drops of e-liquid to the wicking material to prevent dry hits.
4. Insert the New Coil
Align the new coil with the slots in the atomizer base and push it in firmly until it clicks into place.
5. Reassemble the Tank
Place the base back onto the atomizer and hand-tighten the top cap. Avoid overtightening as this can damage the tank.
Tightening the Coil
Tightening the coil is crucial to ensure a secure connection and prevent leakage. Follow these steps to tighten the coil effectively:
- 1. Grip the base: Firmly hold the base of the tank with one hand.
- 2. Align the coil: Align the new coil with the corresponding slots on the base.
- 3. Screw in the coil: Gently screw the coil into the base in a clockwise direction.
- 4. Snug the coil: Use a pair of tweezers or pliers to tighten the coil securely.
- 5. Check for alignment: Ensure that the coil is properly aligned within the airflow channels.
- 6. Tighten further (optional): For a tighter fit, you can use a small hex key or an e-juice bottle to gently tighten the coil further. Avoid overtightening as it can damage the coil or the tank.
The following table provides additional tips for tightening the coil:
| Tip | Benefit |
|---|---|
| Use a clean coil | Prevents contamination and ensures optimal performance |
| Apply a thin layer of e-juice to the coil | Facilitates wicking and reduces dry hits |
| Tighten the coil to a snug fit | Ensures a secure connection and prevents leakage |
| Avoid overtightening | Prevents damage to the coil or the tank |
Priming the Coil
Priming the coil is an important step in the process of changing a coil in the Geekvape Z Tank. By priming the coil, you can help to prevent it from burning out prematurely and extend its lifespan. To prime the coil, follow these steps:
-
Drip a few drops of e-liquid directly onto the cotton in the center of the coil.
-
Allow the e-liquid to soak into the cotton for a few minutes.
-
Screw the coil into the tank.
-
Fill the tank with e-liquid.
-
Allow the tank to sit for a few minutes before vaping, so that the e-liquid can fully saturate the coil.
By priming the coil, you can help to prevent it from burning out prematurely and extend its lifespan.
Additional Tips for Priming the Coil
-
Use a high-VG e-liquid. VG e-liquids are thicker than PG e-liquids, which helps to create a better seal around the coil and prevent it from drying out.
-
Prime the coil multiple times. If you are using a new coil, it is a good idea to prime it multiple times to ensure that the cotton is fully saturated.
-
Be patient. It is important to be patient when priming the coil. Allowing the e-liquid to soak into the cotton for a few minutes will help to prevent it from burning out prematurely.
| Resistance | Coil Type | Wattage Range |
|---|---|---|
| 0.2 ohms | Kanthal A1 | 50-75W |
| 0.4 ohms | Kanthal A1 | 25-45W |
| 0.6 ohms | Kanthal A1 | 15-25W |
Reassembling the Tank
8. Screw the base back into the tank. Make sure the threads are properly aligned and the base is securely tightened.
8a. Insert the coil into the base. Align the coil with the slots in the base and press it into place until it clicks or snaps into position.
8b. Attach the coil to the heating element.
8c. Tighten the top cap onto the tank by turning it clockwise until it is finger-tight.
8d. Fill the tank with e-liquid through the designated filling port.
8e. Replace the mouthpiece onto the top of the tank.
8f. Allow the tank to sit for a few minutes to allow the e-liquid to absorb into the coil before vaping.
Filling the Tank
Slide the top cap open to reveal the fill port, which is on the side of the tank.
| Coil Resistance | Recommended Wattage | Optimal Flavor Range |
| 0.15 Ω | 60-80W | 70-80W |
| 0.2 Ω | 50-65W | 60-65W |
| 0.4 Ω | 25-35W | 30-35W |
| 0.5 Ω | 30-45W | 35-40W |
| 0.8 Ω | 12-18W | 15-18W |
| 1.0 Ω | 10-14W | 12-14W |
| 1.2 Ω | 8-12W | 10-12W |
Hold the tank upside down and insert the coil into the base. Thread the coil clockwise until it is securely tightened. Excess tightening may damage the coil.
Prime the coil by dripping e-liquid onto the cotton inside the coil holes. This will help to prevent burning the coil when you first vape on it.
Reassemble the tank by screwing the top cap back on. Ensure that the fill port is closed before using the tank.
Changing the Coil
1. Unscrew the base of the tank by turning it counterclockwise.
2. Pull the old coil straight out of the base.
3. Prime the new coil by dripping e-liquid onto the cotton inside the coil head.
4. Push the new coil into the base until it clicks into place.
5. Screw the base back onto the tank.
6. Fill the tank with e-liquid.
7. Allow the tank to sit for a few minutes to allow the coil to soak up the e-liquid.
8. Take a few puffs on the tank to prime the coil and remove any excess e-liquid.
9. Adjust the airflow and wattage settings to your desired preference.
10. Enjoy vaping!
Verifying Proper Function
Once you have changed the coil, it is important to verify that it is functioning properly. Here are a few things to look for:
- No leaking: The tank should not leak any e-liquid from the base or the airflow holes.
- Consistent vapor production: The tank should produce a consistent amount of vapor with each puff.
- No burning taste: The vapor should not have a burnt taste.
- No popping or spitting: The tank should not pop or spit e-liquid into your mouth.
- Good flavor: The vapor should have good flavor and not be muted or bland.
- Unscrew the top cap of the tank.
- Pull out the old coil from the base of the tank.
- Insert the new coil into the base of the tank.
- Screw the top cap back onto the tank.
- A burnt taste when you vape
- A decrease in vapor production
- A decrease in flavor
- Leaking from the tank
If you experience any of these problems, it is likely that the coil is not functioning properly. Try replacing the coil with a new one and see if that solves the problem.
Geekvape Z Tank How To Change Coil
Changing the coil in your Geekvape Z Tank is a simple process that can be completed in just a few minutes. Here are the steps on how to do it:
Once you have changed the coil, it is important to prime it before using it. To prime the coil, simply drip a few drops of e-liquid onto the cotton inside the coil. This will help to prevent the coil from burning out when you first use it.
People Also Ask
How often should I change my Geekvape Z Tank coil?
The frequency with which you need to change your Geekvape Z Tank coil will depend on a number of factors, including the type of e-liquid you are using, the wattage at which you are vaping, and how often you vape. However, as a general rule of thumb, you should change your coil every 2-3 weeks.
What are the signs that my Geekvape Z Tank coil needs to be changed?
There are a few signs that may indicate that your Geekvape Z Tank coil needs to be changed. These include:
Can I clean my Geekvape Z Tank coil?
Yes, you can clean your Geekvape Z Tank coil. To do this, simply remove the coil from the tank and rinse it under running water. You can also use a soft brush to gently remove any debris from the coil. Once the coil is clean, dry it thoroughly before reinserting it into the tank.
